Battery for ARP-9

[GothicGhost]

Hello, would this battery fit in stock tube of the ARP-9 okay?

https://nuprol.com/np-power-1100mah-11-1v-20c-stick-type.html

 

Thank you.

 

[MagpieTactical]

I use that exact battery in my ARP556. 

I do have the battery extension unit as well though. 

 

I tried without the extension unit, but it would take a lot of bundling of the wires mosfet etc.  I got the Extension unit at the same time I got the Arp, so never worried about buying batteries that would only fit in the standard stock length

[leadly]

Exactly the same as @MagpieTactical wrote. I used the same battery and winced every time I tried to get the battery and MOSFET in.

 

The battery extension unit takes all the hassle and worry away. It also has some slots on the side to get some airflow in there as it's enclosed with the normal end cap.

 

I sold my ARP9 to fund my MTW but recently won another from an Instagram competition! It's yet to turn up but fingers crossed!!

[GothicGhost]

Thank you, I him got two batteries and the extension bit as well

 

Going to be very happy at xmas.

[MagpieTactical]

That's a different battery to the one you asked about though? 

 

There is a chance that may not fit even with the BEU

[leadly]

• Relieve a cramped environment for your MOSFET and cables to sit to prevent it from over bending and damage.
• Utilize larger battery capacity - perfect if you're running the G&G drum mag as a support role.
• Eliminates the unsteady butt-stock by locking down the two metal rails!
• Maximum battery size approx 152mm long x 19.5mm wide x 11.75mm
• Once installed, the ARP9/556 remains just as compact as before - perfect for CQB use!
• Compatible also with the G&G CM16 Raider L 2.0 E

Above is the description from another site for the battery extension unit,

 

Below is the size of the battery you have purchased

 

 

Product Length	Approx. 11.5cm
Product Height	Approx. 1.6cm
Product Width	Approx. 2.2cm

 

 

Going by the, I read it as your battery will be too wide / thick to fit, as all the extension unit does is allow more length.

[GothicGhost]

Oh I though it was the same pretty much.

 

I will send them back if they don't fit and get the ones I linked first time.

 

Thank you for warning me

Edited November 21, 2021 by GothicGhost

[Chicken pie]

I run the 1450 nuprol battery in my 556 with battery extension. 

Fits ok.

I did have one go dead Sunday half way through the day, however it was a busy morning with lots of bb flying about lol.

 

I also run the 1600mha nuprol,

 

"Nuprol NP 1600mah 11.1v LiPo Stick for Airsoft and RC 8118"

 

it's a bit wider but fits in and defo lasts longer.

 

 

[leadly]

Turns out I fibbed, I asked the lad I sold my ARP9 to, to check what battery I sold him and it was only an 1100mah.

 

@Chicken pie, if your saying those 2 bigger ones fit then I'll try pick one up for the ARP9 I won!

 

 

I look forward to slapping a drum mag under it spraying all day!!

Edited November 23, 2021 by leadly

[Chicken pie]

Yes with battery extension it's pretty easy to fit 1450 or 1600 in.

 

My 1600 lasted all day yesterday, something close to 3500 shots !

[leadly]

Plenty of options then, thank you!

 

I'm in two minds whether to sell my ARP9 or not! Between my MTW, Hi Capa and AAP I don't think I'll get much use out of it!

[Skara]

When I had the arp9 I couldn't fit anything in the pdw stock without the extension.

Now mind you, I did have some extra wiring because of the perun upgrade kit, but still the battery space is too limited!

I ran it on a pair of 11.1s that are roughly 130x17x18 millimetres.

[Epicjake15]

sorry to revive a old forum but i might be getting a arp 9 and i wanted to know what the male tamiya to male dean connector was for and if it was needed