emilianoksa Posted March 28, 2023 Posted March 28, 2023 (edited) I have fitted three Guarder frames to three Marui Glocks - a 22, 34 and 17 Gen4. Two were fine and one needed quite a bit of sanding. The fourth ( 19 Gen 3) has been an absolute ball ache. The holes were badly aligned and I managed to screw up two out of the three chassis pins. The top of the frame was all over the place. I tried to sand it flat and thought I had suceeded but the slide jammed and it took me an hour to get it off with a plastic mallet, ripping up the base of the outer barrel in the process and losing a slide stop spring I will probably never find. In fairness I should point out that the Marui top pin on the 17 Gen 4 (the one that secures the trigger screw) was also a bugger to drive out. Turns out it had nasty spiral tool marks on it. So it isn't just Guarder. It has become extremely difficult to source Marui parts. Even Eagle Six is not particularly well stocked these days. Even some big Far Eastern shops have shortages. Is it possible to get replacement parts direct from Marui if you are outside Japan? I imagine not. I am considering measuring my buggered up chassis pins with calipers and sourcing dowel pins from a UK engineering firm. Has anyone else ever done this? I imagine the TM ones are made of steel. In future I will stick with TM frames even though the ABS gets shiny in no time. I had been considering a Guarder CNC slide and barrel set but after my experience of their quality control I am now reluctant to risk it. Edited March 28, 2023 by emilianoksa
Krisz Posted March 28, 2023 Posted March 28, 2023 (edited) 11 hours ago, emilianoksa said: I have fitted three Guarder frames to three Marui Glocks - a 22, 34 and 17 Gen4. Two were fine and one needed quite a bit of sanding. The fourth ( 19 Gen 3) has been an absolute ball ache. The holes were badly aligned and I managed to screw up two out of the three chassis pins. The top of the frame was all over the place. I tried to sand it flat and thought I had suceeded but the slide jammed and it took me an hour to get it off with a plastic mallet, ripping up the base of the outer barrel in the process and losing a slide stop spring I will probably never find. In fairness I should point out that the Marui top pin on the 17 Gen 4 (the one that secures the trigger screw) was also a bugger to drive out. Turns out it had nasty spiral tool marks on it. So it isn't just Guarder. It has become extremely difficult to source Marui parts. Even Eagle Six is not particularly well stocked these days. Even some big Far Eastern shops have shortages. Is it possible to get replacement parts direct from Marui if you are outside Japan? I imagine not. I am considering measuring my buggered up chassis pins with calipers and sourcing dowel pins from a UK engineering firm. Has anyone else ever done this? I imagine the TM ones are made of steel. In future I will stick with TM frames even though the ABS gets shiny in no time. I had been considering a Guarder CNC slide and barrel set but after my experience of their quality control I am now reluctant to risk it. Hm. I put together a Marui G26 using a Guarder frame with a custom made slide and built a Marui G17 Gen. 4 using Guarder frame and Guarder alu slide. No sanding/issues/swearing. It seems you need luck in airsoft just like in real life. My go to usually Armsaholic, Boomarms, Rainbow8, Ehobbyasia etc. regarding parts. You certainly able to buy parts from Impluse101 but shipping isn't gonna cheap. Marui does only care about domestic market I'd very suprised if you could get parts from them directly. Edited March 29, 2023 by Krisz
emilianoksa Posted March 28, 2023 Author Posted March 28, 2023 Thanks. I looked at Impulse but they didn't have the parts I want.
Krisz Posted March 29, 2023 Posted March 29, 2023 8 hours ago, emilianoksa said: Thanks. I looked at Impulse but they didn't have the parts I want. Np. Let me know what kind of slide stop spring you need coz I've got an extra I don't need anyway. If it's important.
emilianoksa Posted March 29, 2023 Author Posted March 29, 2023 Very kind of you. I'll bear that in mind.
Davegolf Posted March 29, 2023 Posted March 29, 2023 On 28/03/2023 at 20:43, Krisz said: Hm. I put together a Marui G26 using a Guarder frame with a custom made slide and built a Marui G17 Gen. 4 using Guarder frame and Guarder alu slide. No sanding/issues/swearing. It seems you need luck in airsoft just like in real life. My go to usually Armsaholic, Boomarms, Rainbow8, Ehobbyasia etc. regarding parts. You certainly able to buy parts from Impluse101 but shipping isn't gonna cheap. Marui does only care about domestic market I'd very suprised if you could get parts from them directly. Hi, I’m looking to get a slide for my pistol from Boomarms, how have you found them? Ive not used them before. TIA
Guest Posted March 29, 2023 Posted March 29, 2023 38 minutes ago, Davegolf said: Hi, I’m looking to get a slide for my pistol from Boomarms, how have you found them? Ive not used them before. TIA Terrible comms but excellent products, always arrive on time
Davegolf Posted March 29, 2023 Posted March 29, 2023 That’s the important part! Hopefully my Ali ACRO will arrive soon.
Krisz Posted March 30, 2023 Posted March 30, 2023 (edited) 9 hours ago, Davegolf said: Hi, I’m looking to get a slide for my pistol from Boomarms, how have you found them? Ive not used them before. TIA I don't think I asked them about anything but had no issues regarding delivery or the product. Some of these HK retailers don't give a damn about you and then on the other hand you've got rainbow8 or ehobbyasia who answer every email. Edited March 30, 2023 by Krisz
Recommended Posts